Tür "conferenceObject" Mühendislik ve Mimarlık Fakültesi için listeleme
Toplam kayıt 34, listelenen: 1-20
-
Beyincik Sarkması Tip-I Hastalarında Beyincik Gri Maddesinin Fraktal Boyut Analizi
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)Chiari Malformation type I (CM-I), which is described as the elongation of cerebellar tonsils below the foramen magnum through the spinal canal, is a serious congenital or acquired neurological disorder. The purpose of the ... -
CFD Based Wind Assesment in West of Turkey
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)Wind is an important renewable source which has a large potential all around the world. Recently, wind energy has been quite popular and owns a growing market in Turkey. This expansion brings more investigation around the ... -
A Consideration of Loss Component in Model Control DC-DC Converter
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015-11-22)Recently, the energy saving is required. It is necessary for the energy saving to operate the electric device in the sleep mode. Therefore, the output voltage rises abnormally because the dc-dc converter is required the ... -
A Consideration of Signal Frequency Detector in Digital Peak Current Mode DC-DC Converter
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015-11-22)The purpose of this paper is to reveal the designing of the static characteristic of the digital peak current mode dc-dc converter using a voltage controlled oscillator (VCO). In the proposed method, it is able to sample ... -
A Consideration of Transient Response for Sensorless Model Control DC-DC Converter
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)The purpose of this paper is to discuss a current prediction algorithm for sensorless model control dc-dc converter. In the proposed method, the sensing resistor for the current detection is eliminated by predicting the ... -
Controller Design for a Limited Angle Torque Motor and dsPIC Implementation
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)This study addresses the modeling of a LAT motor in Simulink environment and then designing and testing various controllers for this model. The LAT motor model is first expressed using equations which describe the DC motor ... -
Democratization of University Management for Quality Higher Education
(ELSEVIER SCIENCE BV, SARA BURGERHARTSTRAAT 25, PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS, 2012-06-21)The objective of this paper is to provide some insights for developing a high quality university through democratizing the contemporary university management practices. The high quality university has often the quality ... -
Design a Grid Tie Inverter for PMSG Wind Turbine using FPGA & DSP Builder
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2016)The recent makeshift in fuel choice, renewable energy sources has been considered as the most popular form of its kind because of its environment friendly approaches, less cost tariff policy and the natural fuel abundance. ... -
Design and experimental implementation of single phase power factor correction converter based on fuzzy logic controls techniques
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)This paper presents an experimental implementation of the single phase power factor corrector PFC based on AC/DC converter with boost chopper. PI, Fuzzy logic and fuzzy adaptive PID controllers for the capacitor voltage ... -
Design of A Computer Controlled Speed Control System for Wound-Rotor Inducion Machines
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)This study introduces a novel and powerful speed control system with computer interface for wound-rotor induction machines (WRIM). In order to improve the sensitivity and stability of the control process, a high-speed ... -
Design of Power Control Unit for Heat Recovery Device Used in Renewable Energy System
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015-11-22)Heat recovery devices are used for saving energy especially for the renewable energy systems because of effective usage of electrical energy while providing air conditioning in spaces which needs fresh air. These devices ... -
Designing a Competitive Electric Vehicle Charging Station with Solar PV and Storage
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)An electrical vehicle charging station is a charging power supply for electrical vehicles. This paper proposes design of a model for a PV based electrical vehicle that forecasts total power output under particular conditions ... -
Digital PID Based Two-Compensator for DC-DC Converter
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)The purpose of this paper is to present the performance characteristics of the digital PID based two-compensator for the dc-dc converter. Authors have already presented a fast PD control method, which can reduce the influence ... -
Digitally Proportional Gain Varying Method for DC-DC Converter
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)The purpose of this paper is to propose a digitally proportional gain varying method for dc-dc converter. In the proposed method, the proportional gain is set to a small value in the steady state and is changed to a large ... -
EB Varestraint Test Method and an Application
(The International Council of the Aeronautical Sciences (ICAS), 2002)The Varestraint Test is applied to understand microcrack after GTA welding. However, The EB (Electron Beam) Varestraint Test is a new method, which tests sıitabilty of the source for EB Welding in aero engine and ... -
Effect of infill wall and wall openings on the fundamental period of RC buildings
(WIT PRESS, ASHURST LODGE, SOUTHAMPTON SO40 7AA, ASHURST, İNGİLTER, 2013-07-08)The effect of infill walls to stiffness of the structures has been known for a long time and this effect has taken many of the earthquake regulations with empirical relationships and equations into account. However, in ... -
The Implementation of Additive Manufacturing Technologies in Aircraft Maintenance, Repair, And Overhaul (MRO) Operations
(İksad Publishing House, 2021)Chip-away technologies are traditional manufacturing methods based on the principle of taking-out particles from a large workpiece employing cutting tools. Its origins date back centuries. On the other hand, Additive M ... -
An Improved dynamic battery model suitable for photovoltaic applications
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015)Modeling of batteries used in photovoltaic applications has been a real issue for many research groups due to its complex electrochemical and electrical behavior. In this paper, we propose an improvement of the Battery ... -
Improvement for Fast Response of Current Sensorless Model Control DC-DC Converter
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2016)The switching power supply is required the wide load range operation for the energy saving. In such a situation, the output voltage must be regulated. The model control is able to regulate the output voltage, because the ... -
Improvement in Transient Response of Fast P Control DC-DC Converter with Static Model
(IEEE, 345 E 47TH ST, NEW YORK, NY 10017 USA, 2015-11-22)The purpose of this paper is to propose the digital control method that is comprised of the fast P control and model control for an improvement of the transient response of the dc-dc converter. The electronic devices are ...